40代・50代・60代・70代の友達作り・趣味探し・交流サイト

文字の大きさを変える
投稿者
FSPCBA さんの日記
アクセス数: 1405 



カテゴリー
月表示
交流しよう
PR2
TOP  >  ハピブロ(日記・blog)  >  FSPCBA  >  pcb,pcba  >  Considerations for Designing Clock PCBs-FS Technology

FSPCBA さんの日記

 
2022
7月 1
(金)
11:08
Considerations for Designing Clock PCBs-FS Technology
本文

The clock crystal and associated circuits should be placed in the center of the PCB and should have a good ground plane, not close to the I/O interface. Clock generation circuits are not allowed in the form of daughter cards or daughter boards, and must be fabricated on separate clock boards or load-bearing boards. Only the equipment related to the clock circuit is installed in the PCB clock circuit area of FS TECH, avoid installing other circuits. Other signal lines should not be routed near or below the crystal: Clock circuits and ground planes are used under the crystal if other signals pass through the plane violating the image plane function. If the signal passes through the ground plane, there will be a small ground loop and affect the continuity of the ground plane.

Ground loops will have problems at high frequencies

Shielding measures can be used to shield the clock crystal and clock circuit;

If the clock case is metal metal, the PCB design must have copper under the crystal, and this part has a good electrical connection to the complete ground (through a porous ground). Advantages of laying ground under the FS Tech clock: The circuits inside the crystal oscillator generate RF currents. If the crystal is encased in a metal case, the DC power source discharges the transient current generated by the case through RF radiation through the ground plane, referenced to the DC voltage and the RF current circuit within the crystal.

fs tech
In short, the metal casing is a single-ended antenna, and the nearest image layer, the ground plane layer, sometimes has two or more radiation coupling effects, as the RF current to the ground.

The bottom of the PCB crystal is also conducive to heat dissipation

The clock circuit and crystal ground will provide an image plane that reduces the common mode currents of the associated crystal and clock circuit, thereby reducing RF emissions. Ground can also absorb differential mode RF currents. This plane must be connected to the complete ground plane through multiple points and through multiple holes, which provides low impedance. To improve the effect of the ground plane, the clock circuit of FS Technology should be close to the ground plane. Since most of the surface mount crystals are packaged in plastic, the SMT packaged crystal has more RF energy radiation than the metal shell crystal, and the RF current in the crystal will radiate into the space and be coupled with other devices.

FS Technology-Only improve high-quality PCB assembly services for customers

閲覧(283)
コメントを書く
コメントを書くにはログインが必要です。
おすすめ情報
あなたのページへログイン
ユーザー名:

パスワード:
SSL  | パスワード紛失  | 新規登録
新規登録メンバー

お蛾夫人
女性 関東エリア
ケン1984 東京
miaiyako 女性 東京
かおりかおり 女性 大阪
monaco 女性 愛知県
マッツ 東京
スクエア 男性 広島
富士さんNo2 女性 千葉県
mario 男性 愛知県
彩夏 女性 東京


PRコーナー
ハピスロ世代について このサイトの使い方 | メンバー登録 | 困ったときは | 事務局からのお知らせ | ご利用規約 | プライバシーポリシー | 会社概要 | 広告掲載に関して | お問い合わせ | リンク集
メンバーコンテンツ メンバー検索 | なかよし広場(コミュニティ) | ハピスロ日記(ブログ)写真投稿コーナー出会いの広場交流掲示板異世代交流サロン体のお悩み掲示板
お楽しみ情報 イベントカレンダーあれこれ気になる調査隊オススメ穴場スポット素敵にアンチエイジング歌声フォークソング懐かしの歌声ホール
趣味の情報 街歩き | 山歩き | ウォーキング・ジョギング | レシピ | グルメスポット | DIY/日曜大工 | 手芸 | 陶芸 | ダンス | 歌・カラオケ | 楽器
運営: アトムブラザーズ音楽出版株式会社 © 2012